Picture below is overall internal architecture of worker which shows its defined classes with private variables and public functions. Vector version of this picture is available [here](https://github.com/ReCodEx/wiki/raw/master/images/Worker_Internal_Architecture.pdf).
Worker specific requirements are written in this section. Some parts of this guide may be different for each type of worker, for example Compiler principles worker is not fully covered here.
**Install libarchive library** (optional)
Installing this package will only speed up build process, otherwise libarchive is built from source.
- Debian package is `libarchive-dev`.
- RedHat packages are `libarchive` and `libarchive-devel`. These are probably not available for RHEL.
First, we need to compile sandbox Isolate from source and install it. Current worker is tested against version 1.3, so this version needs to be checked out. Assume that we keep source code in `/opt/src` dir. For building man page you need to have package `asciidoc` installed.
For proper work Isolate depends on several advanced features of the Linux kernel. Make sure that your kernel is compiled with `CONFIG_PID_NS`, `CONFIG_IPC_NS`, `CONFIG_NET_NS`, `CONFIG_CPUSETS`, `CONFIG_CGROUP_CPUACCT`, `CONFIG_MEMCG`. If your machine has swap enabled, also check `CONFIG_MEMCG_SWAP`. Which flags was your kernel compiled with can be found in `/boot` directory, for example in `/boot/config-4.2.6-301.fc23.x86_64` file for kernel version 4.2.6-301. Red Hat distros should have these enabled by default, for Debian you you may want to add the parameters `cgroup_enable=memory swapaccount=1` to the kernel command-line, which can be set using `GRUB_CMDLINE_LINUX_DEFAULT` in `/etc/default/grub`.
For better reproducibility of results, some kernel parameters can be tweaked:
- Disable address space randomization. Create file `/etc/sysctl.d/10-recodex.conf` with content `kernel.randomize_va_space=0`. Changes will take effect after restart or run `sysctl kernel.randomize_va_space=0` command.
- Disable dynamic CPU frequency scaling. This requires setting the cpufreq scaling governor to _performance_.
_**TODO** - do we really need it and is it worth higher power consumption? [Red Hat setup](https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Power_Management_Guide/cpufreq_governors.html), [Debian setup](https://wiki.debian.org/HowTo/CpuFrequencyScaling)_
Note that `rpm` and `deb` packages are build in the same time. You may need to have `rpmbuild` command (usually as `rpmbuild` or `rpm` package) or edit CPACK_GENERATOR variable _CMakeLists.txt_ file in root of source code tree.
- Install generated package through your package manager (`yum`, `dnf`, `dpkg`).
_Note:_ If you don't want to generate binary packages, you can just install the project with `make install` (as root). But installation through your distribution's package manager is preferred way to keep your system clean and manageable in long term horizon.
### Install worker on Windows
From beginning we are determined to support Windows operating system on which some of the workers may run (especially for projects in C# programming language). Support for Windows is quite hard and time consuming and there were several problems during this. To ensure capability of compilation on Windows we set up CI for Windows named [Appveyor](http://www.appveyor.com/). However installation should be easy due to provided installation script.
There are only two additional dependencies needed, **Windows 7 and higher** and **Visual Studio 2015+**. Provided simple installation batch script should do all the work on Windows machine. Officially only VS2015 and 32-bit compilation is supported, because of hardcoded compile options in installation script. If different VS is needed or different platform, script should be changed to appropriate values, it should be quite simple and straightforward.
Mentioned script is placed in *install* directory alongside supportive scripts for UNIX systems and is named *win-build.cmd*. Provided script will do almost all the work connected with building and dependency resolving (using **NuGet** package manager and **msbuild** building system). Script should be run under 32-bit version of **Developer Command Prompt for VS2015** and from *install* directory.
Building and installing of worker is then quite simple, script has command line parameters which can be used to specify what will be done:
* *-build* - Don't have to be specified. Build worker and all its tests, all is saved in *build* folder and subfolders.
* *-clean* - Cleanup of downloaded NuGet packages and built application/libraries.
* *-test* - Build worker and run tests on compiled test cases.
* *-package* - Clickable installation generation using cpack and NSIS. [NSIS](http://nsis.sourceforge.net/) have to be installed on machine to get this to work.
```
install> win-build.cmd # same as: win-build.cmd -build
For evaluating jobs you have to install tools that fit your needs. Here are some useful tips of different compillers to install.
**C/C++**
For compiling C and C++ programs is used `GCC` compiler. Maybe you could install install most of the staff by executing following command, but it's not needed.
```
# yum group install "Development Tools"
```
To install the compiler separately, you could install it from the distribution's repositories.
```
# yum install gcc gcc-c++ make
```
To get reasonably new version, you may consider installing [Red Hat Developer Toolset 4](https://access.redhat.com/documentation/en-US/Red_Hat_Developer_Toolset/4/html-single/4.0_Release_Notes/index.html), or install these from Fedora repo. In Debian, _testing_ repo can be used.
**C\#**
For new versions of **Mono**, we'll use [Xamarin repositories](http://www.mono-project.com/download/#download-lin). For Red Hat based OS:
Free Pascal compiler 3.0.0 can be downloaded as `rpm` packages from [official website](http://www.freepascal.org/down/x86_64/linux-austria.var). In Debian, this version is [experimental](https://packages.debian.org/experimental/fpc-3.0.0), but seems to be stable enough.
Following text describes how to set up and run **worker** program. It's supposed to have required binaries installed. For instructions see [[Installation|Worker#installation]] section. Also, using systemd is recommended for best user experience, but it's not required. Almost all modern Linux distributions are using systemd now.
- create _systemd_ unit file `/etc/systemd/system/recodex-worker@.service`
- put main binary to `/usr/bin/recodex-worker`
- put judges binaries to `/usr/bin/recodex-judge-normal`, `/usr/bin/recodex-judge-shuffle` and `/usr/bin/recodex-judge-filter`
- create system user and group `recodex` with `/sbin/nologin` shell (if not existing)
- create log directory `/var/log/recodex`
- set ownership of config (`/etc/recodex`) and log (`/var/log/recodex`) directories to `recodex` user and group
### Default worker configuration
Worker should have some default configuration which is applied to worker itself or may be used in given jobs (implicitly if something is missing, or explicitly with special variables). This configuration should be hardcoded and can be rewritten by explicitly declared configuration file. Format of this configuration is yaml like in the job config.
#### Configuration items
Mandatory items are bold, optional italic.
- **worker-id** - unique identification of worker at one server. This id is used by _isolate_ sanbox on linux systems, so make sure to meet isolates requirements (default is number from 1 to 999).
- **broker-uri** - URI of the broker (hostname, IP address, including port, ...)
- _broker-ping-interval_ - time interval how often to send ping messages to broker. Used units are milliseconds.
- _max-broker-liveness_ - specifies how many pings in a row can broker miss without making the worker dead.
- _threads_ - information about available threads for this worker
- **hwgroup** - hardware group of this worker. Hardware group must specify worker hardware and software capabilities and it's main item for broker routing decisions.
- _working-directory_ - where will be stored all needed files. Can be the same for multiple workers on one server.
- **file-managers** - addresses and credentials to all file managers used (eq. all different frontends using this worker)
- **hostname** - URI of file manager
- _username_ - username for http authentication (if needed)
- _password_ - password for http authentication (if needed)
- _file-cache_ - configuration of caching feature
- _cache-dir_ - path to caching directory. Can be the same for mutltiple workers.
- _logger_ - settings of logging capabilities
- _file_ - path to the logging file with name without suffix. `/var/log/recodex/worker` item will produce `worker.log`, `worker.1.log`, ...
- _level_ - level of logging, one of `off`, `emerg`, `alert`, `critical`, `err`, `warn`, `notice`, `info` and `debug`
- _max-size_ - maximal size of log file before rotating
Isolate is used as one and only sandbox for linux-based operating systems. Headquarters of this project can be found at [https://github.com/ioi/isolate](https://github.com/ioi/isolate) and more of its installation and setup can be found in [Installation](#installation) section.
// TODO: further desc
#### Limit isolate boxes to particular cpu or memory node
New feature in isolate is possibility of limit isolate box to one or more cpu or memory node. This functionality is provided by cpusets kernel mechanism and is now integrated in isolate. It is allowed to set only `cpuset.cpus` and `cpuset.mems` which should be just fine for sandbox purposes. As kernel functionality further description can be found in manual page of cpuset or in linux documentation in section `linux/Documentation/cgroups/cpusets.txt`. As previously stated this settings can be applied for particular isolate boxes and has to be written in isolate configuration. Standard configuration path should be `/usr/local/etc/isolate` but it may depend on your installation process. Configuration of cpuset in there is really simple and is described in example below.
```
box0.cpus = 0 # assign processor with id 0 to isolate box with id 0
box0.mems = 0 # assign memory node with id 0
# if not set linux by itself will decide where should sandboxed program run
box2.cpus = 1-3 # assign range of processors to isolate box with id 2
box2.mems = 4-7 # assign range of memory nodes
box3.cpus = 1,2,3 # assign list of processors to isolate box with id 3
```
**cpuset.cpus:** Cpus limitation will restrict sandboxed program only to processor threads set in configuration. On hyperthreaded processors this means that all virtual threads are assignable not only the physical ones. Value can be represented by single one, list of values separated by commas or range with hyphen delimiter.
**cpuset.mems:** This value is particularly handy on NUMA systems which has several memory nodes. On standard desktop computers this value should always be zero because only one independent memory node is present. As stated in `cpus` limitation there can be single value, list of values separated by comma or range stated with hyphen.
